Titanium Carbide has the chemical formula, TiC and a molecularweight of 59.89. The grey powder can be used to produce cemented carbide.
Particle size: -325mesh
Learn more about Titanium Carbide powder
This is TiC with a molecular mass of 59.89. It is gray-colored, with a face-centered cubic lattice structure. Titanium carbide melting points are 314090°C. Titanium carbide boil point at 4820°C. The relative density of 4.93 is also available. It is harder than 9. The hardness is greater than 9. TiC compounds are stable when they are lower than 800. They can also react with pure oxygen when their levels exceed 1150.
The refractory ceramic material TiC made of titanium carbide is extremely hard, with a Mohs 9.9–9.5. It’s similar to the tungsten carbide. It appears as a dark powder with a crystal structure of sodium chloride (face center cubic). It has an elastic modulus around 400 GPa and a shear modus of 188 GPa.
Titanium carbonide can be seen in nature as the very rare mineral Rhodochrosite. (TiV, Fe), C. It is located near Uzbekistan’s border in the Chagar Region of the Soviet Union. The crystals are 0.3 to 0.1 mm in size.
To obtain the Titanium carbide pricing, please send us an inquiry.
Titanium Carbide TiC powder –
The molecular weight for the chemical TiC formula is 59.89. Gray metallic lustrous crystal solid. Its melting point and boiling point are 3140 and 4820 respectively. The relative density of 4.93 is also available. Hardness 9-10. Water insoluble, aqua regia soluble in nitric Acid and water insoluble. It reacts with pure oxygen at 1150 and is therefore stable when the temperature is below 800. Also used for the production of cemented carbide.
Technical Parameters of Titanium Carbide TIC Powder:
How Titanium Carbide TIC Powder is produced?
There are many methods to make titanium carbide. The most commonly used are these:
1. Carbothermic method of reduction
Use carbon black to reduce TiO2, the reaction temperature range is 1700-2100, and the chemical reaction formula is TiO2(s)+3C(s)=TiC(S)+2CO(g).
2. Direct carbonization
TiC can be created when Ti powder and carbon are combined. It is a chemical reaction that produces TiC. It is very difficult to produce sub-micron level Ti powder. This limit is why this technique is not widely used. It takes between five and twenty hours for the above reaction to occur. The reaction is also difficult to monitor. Further grinding of the reactants is needed to make fine particles. Granular TiC powder. To obtain a more pure product it is important to chemically remove the fine powder from ball milling.
3. Chemical vapor deposition
A synthesis process uses the reaction of TiCl4,H2 and C. This reactant is heated to form hot tungsten and carbon monofilaments, which then allows TiC crystals to grow on that monofilament. There are strict quality and output limits for the TiC powder produced by this process. Due to TiCl4 (the product), the HCl in it can be strongly corrosive so it’s important that you take care when synthesizing them.
4. Sol-gel method
Method for making small particles by mixing materials thoroughly and dispersing them with a solution. Although it has some advantages such as good chemical uniformity and small particles size, narrow distribution and low heat treating temperature, this method is complicated and can result in large drying shrinkage.
5. Microwave technique
Nano TiO2 (or carbon black) can be used as raw materials. Next, apply the principle of carbothermal reduction to heat the material using microwave energy. The high frequency electric field converts microwave energy to heat energy by using the dielectric losses of the materials. This is how nano-TiO2O2 and carbon can be made into TiC.
6. Blast impact method
Mix the titanium dioxide powder with the carbon powder in a specific proportion. To make the precursor, a cylindrical of 10mm5mm is used. It has a density of 1.5g/cm3. The laboratory is then placed inside a metal constrained outer tube. The experiment will be carried out in an explosion container made by you. You can also collect detonation-ash from the blast shock wave. Large impurities like iron filings and other small particles are removed during the preliminary sieving. The result is a black powder. After 24 hours in water, the brownish-colored powder is soaked in aqua regia. Finally, it’s put into a muffle furnace where 400 minutes of calcining at 400°C will give you a silvery-gray powder.
7. Carothermic low-frequency high-frequency reduction technique
The pigment-grade titanium dioxide and charcoal powder should be weighed and mixed at 1:3 or 1:4. Next, mill them for 6–10 hours on a planetary mill at 300-400 r/min. Make a 2-cm2cm2cm4cm-sized block using the tablet press. Finally, pour the material into the graphitecrucible. Add argon gas to protect the area. Adjust the current to 500A to cause the material to go through a carbothermal reduction process. Once the heat preservation has been completed, the product reduced to room temperature is cooled under an atmosphere of argon. Then, take out the material and grind and crush it until you get ultra-fine Titan carbide powder.
Titanium Carbide TIC Application:
Most people use titanium carbide to create cemented carbide. This is also used for electrodes and abrasives in arc lamps.
1. Use titanium carbide powder for high-temperature heat spraying, welding, materials, hard films, military aviation, and hard alloys, as well as cermets.
2. In order to increase wear resistance in thermostors, Titanium carbide can be used.
3. A NaCl-type cubic structure of Titanium carbide is used to make the powder. TiC-WC solid solutions with WC are formed by adding 6% to 30% TiC to the WC-Co cemented caride. This will increase the alloy’s red heat resistance as well as its wear resistance.
4. Titanium carbide can be used to process steel better than WC-Co Cemented Carbide. It has both anti-oxidation as well as anti-corrosion characteristics.
5. You can make titanium carbide by using alloys like Ni-Mo to create tungsten free cemented carbide. This will increase your turning speed, accuracy, and smoothness.
6. To prepare cermets of titanium carbide. These are used for high-speed steel processing.
7. The wear-resistant coating of titanium carbide on metal components such as knives heads or watch mechanisms is another use for it.
8. Titanium carbide coated: This coating is useful for thermal insulation and re-entry into the atmosphere of a spacecraft.
Storage condition of Titanium Carbide Powder:
Titanium Carbide TiC Powder needs to be stored in an airtight container. Additionally, it should not be subject to extreme stress.
Shipping and Packing of Antimony Selenide sb2Se3 powder :
Titanium Carbide Powder Packaging: Vacuum Packing, 1kg/bag 25kg/barrel or on your Request
Shipping information for Titanium Carbide TiC Pulp : will be shipped by sea or air as soon as the payment is received.
Luoyang Tongrun Nano Technology Co. Ltd.
We can provide high-quality titanium carbide dust. Please contact us to send an inquiry. (firstname.lastname@example.org)
Titanium Carbide Properties
Titanium Carbide Health & Safety Information